Concrete Testing Machines
Air Entrainment Meter For Testing Lab For Concrete Testing Lab
Air Entrainment Meter for Concrete Testing - As entrainment of air in limited percentage improves durability of concrete and very low percentages deteriorate it ,measurement of air entrapped in freshly mixed concrete becomes important.
The use of chemical additives to increase work ability of concrete in turn requires an air content check to be made. Air entrainment meters are used to determine air entrained in freshly mixed concrete by pressure method.
Specification
- The apparatus consists of a pressure tight flanged cylindrical measuring bowl of 0.005 cubic meter capacity for maximum size of aggregate 38mm.
- The bowl is fitted with a removable flanged conical cover assembly with the help of a seal.
- The conical cover has an air valve and a petcock for bleeding off the water.
B Type Air Entrainment Meter For Testing Lab For Concrete Testing Lab
B Type Air Entrainment Meter for Concrete Testing - It consists of an aluminium vessel with built in hand operated pressure pump, connected to the measuring gauge showing directly the air content in percentage.
Permeability Apparatus (Three Cell Model) For Testing Lab For Concrete Testing Lab
Permeability Apparatus (Three Cell Model) for Concrete Testing - Same as NCOT-C41 but supplied with three individual cells with stand. Three pressure gauges for indicating pressure in each cell are supplied apart from the main pressure gauge .
Permeability Apparatus (Single Cell Model) For Testing Lab For Concrete Testing Lab
Permeability Apparatus (Single Cell Model) for Concrete Testing - One of the durability test of concrete is to determine permeability of water through specimen. Permeability apparatus is used for determining the permeability of cement mortar and concrete specimens of 15cm cubes cast in the laboratory.
Specification
The concrete permeability apparatus comprises of a brass / gunmetal cell of Square/Round cross-section mounted on a stand and a pressure chamber is connected to the cell through copper tubing and T-connector mounted on the stand with sleeve packed valve and rubber hose pipe with end connections. The cell assembly consists of one base plate, one metal funnel and one top plate.
Compression Testing Machine (Automatic) For Testing Lab For Concrete Testing Lab
Compression Testing Machine (Automatic) for Concrete Testing - Automatic range of 2000 kN and 3000 kN capacity compression testing machines has been designed to meet the need for reliable and consistent testing of concrete samples.
All our machines feature the complete automatic test cycle with a closed loop digital readout. Once the specimen parameters have been introduced, it is sufficient to press the START button to complete the test. Compression machines consist of their main parts: Frame, power pack and data acquisition & control system.
Compression Testing Machine For Testing Lab For Concrete Testing Lab
Compression Testing Machine for Concrete Testing - Range of Semi Automatic concrete compression machines give users the ability to test and analyses concrete samples in accordance with all major international standards. The power pack incorporates a durable variable output pump, allowing fine control for accurate load pacing, or maximum pump output for daylight closure.
The rapid approach pump provides a high rate of daylight closure and is available as an optional extra for the motorised power pack- only if fitted at the time of ordering. An onboard LED screen allows the sample load / Stress to be monitored. The control panel allows for data input and manual control if required.
Flexure Testing Machine For Testing Lab For Concrete Testing Lab
Flexure Testing Machine for Concrete Testing - The Flexure Strength Testing are designed to test flexural strength of concrete beams. The design provide maximum rigidity throughout their working range. The load is applied by the downward movement of the piston. A spacer is for testing different size of beams.
The load is indicated on a calibrated bourdon tube type load gauge of range: 0 - 100 kN x 0.5 kN (0- 1O,000 kgf x 50 kgf). The load gauge is calibrated against National Council for Cement and Building Materials Certified Proving Ring. Flexure Testing Machines 1. Light weight, rugged high strength frame 2. Double action hydraulic pump 3. Self-aligning roller assembly 4.
Compression Testing Machine (Four Pillar Nut Model) Hand Cum Electrical Operated For Testing Lab For Concrete Testing Lab
Compression Testing Machine (Four Pillar Nut Model) Hand cum Electrical Operated for Concrete Testing - The load frame is made up of high quality steel construction with a fixed. Upper lead carrying a ball seated platen. 4 pillars are fixed to the base and the top plate of the loading frame.
The upper and lower plates are adjusted with the help of head screw on either side of the pillar. The ram dia of the machine varies from the requirements of the customer. The lower pattern are at the base of the frame above the ram and it is rectangular in shape. Sufficient clearance is provided between the platens to fit in the cylindrical/ cube moulds.
Compression Testing Machine (Channel Type Load Frame) Hand Operated For Testing Lab For Concrete Testing Lab
Compression Testing Machine (Channel Type Load Frame) Hand Operated for Concrete Testing - In these load frames “C” channels are used, they are welded at the top as well as bottom and with stand high loads.
A hydraulic jack is fitted at centre of the base of the load frame, over which can be fitted lower platen and spacer block with the help of centering pin. A lead screw passes through the top of the frame. To the lower end of this lead screw is fixed the upper platen with spherical seat for self alignment. The platens are accurately machined, hardened and polished. The lower platen grooves to correctly place the specimen.
Compression Testing Machine (Pillar Type Load Frame) Hand Operated For Testing Lab For Concrete Testing Lab
Compression Testing Machine (Pillar Type Load Frame) Hand Operated for Concrete Testing - These are four pillar type load frames. Four solid pillars are vertically fixed to a sturdy base and at other end is fixed a cross head.
The height of the cross head is also slightly adjustable. A gauge 200mm is fixed in the centre of cross head. To the lower end of this lead screw is fixed upper platen with a spherical seat for self alignment. At the centre of the base plate is fixed a jack, on the top of which the lower platen with the help of a centering pin is kept. The distance between the upper and lower platen is variable by means of the lead screw. A spacer block is also supplied with the load frame.
Micro Controller Based Automatic Compression Testing Machine For Testing Lab For Concrete Testing Lab
Micro Controller Based Automatic Compression Testing Machine for Concrete Testing - The Automatic Compression Testing Machine has all features of Micro Controller based Compression Testing Machine. In addition, it has: An automatic load release facility.
Support for data transmission over distances upto several kilometers. This is useful for testing in the field. (Optional feature). Measurements of Strain with a resolution of upto 0.001 mm (optional feature). Measurement of Flexural Strength (optional feature).
Automatic Compression Testing Machine For Testing Lab For Concrete Testing Lab
Automatic Compression Testing Machine for Concrete Testing - The Automatic Compression Testing Machine is a fully automated version of the manual / semi automatic Compression Testing Machine.
The machine is available in 500kN, 1000kN, 2000kN, 3000kN, 5000kN Ranges. It has provision for automatically turning the pump on and off, controlling the set pace rate and switching the machine off under predetermined conditions. The Control release the pressure at the end of every run and reinitializes the machine at the beginning of every test.
Micro Controller Based Compression Testing Machine For Testing Lab For Concrete Testing Lab
Micro Controller Based Compression Testing Machine for Concrete Testing - Operation of Micro Controller based Compression Testing Machine are controlled by an intelligent Pace Rate Controller. This facilities Automatic Pace Rate Control, Data Logging, Data Printing, Load Hold etc. It has a full 3 term PID feed back control which uses a high torque Stepper Motor. It consists of a Loading Unit, an Electrically Operated Hydraulic Pump and an Intelligent Pace Rate Controller. Micro Controller based Compression Testing Machine is available in all models from 50kn to 3000kN capacity.
Digital Compression Testing Machine For Testing Lab For Concrete Testing Lab
Digital Compression Testing Machine for Concrete Testing - The Digital Compression Testing Machine has been designed to meet the need for a simple, economic and reliable means to test concrete for its compressive strength.
The design emphasizes simplicity, both of construction and operation, and makes the machine easy to use and maintain. The unit is compact, making its useful for site applications. The digital machines are provided with a pace rate indicator to indicate pace rate on a Bar Graph. With a little experience, the pace rate can be manually adjusted while the test is in progress.
Analogue Compression Testing Machine For Testing Lab For Concrete Testing Lab
Analogue Compression Testing Machine for Concrete Testing - Compression Testing Machines Loading Unit : - The loading unit is of fully welded construction having a cross head, base and solid side plates. The hydraulic jack is fixed to the base. The platens of the machine are hardened, ground and polished. The upper platen is provided with self-alingning action. To facilitate testing of various size specimens, suitable size spacers are provided
Density Of Fresh & Hardened Concrete For Testing Lab For Concrete Testing Lab
Density of Fresh & Hardened Concrete for Concrete Testing - The density of both fresh and hardened concrete is of interest to the engineer for numerous reasons including its effect on durability, Strength and resistance to permeability. Hardened concrete density is determined either by simple dimensional checks, followed by weighing and calculation or by weight in air / water buoyancy methods.
Sand Adsorption Cone And Tamper For Testing Lab For Concrete Testing Lab
Sand Adsorption Cone and Tamper for Concrete Testing - Used for determining the slump of fine aggregate in the determination of bulk and apparent specific gravity and absorption of fine aggregate. The equipment comprises of a conical metal mould 1.5inch dia at to 27/8 top, 3.5 inch dia at base and 2 inch in height.
Longitudinal Compressometer For Testing Lab For Concrete Testing Lab
Longitudinal Compressometer for Concrete Testing - Designed for finding out the deformation and strains on 15cms. Diameter and 30 cms high cement and concrete cylinders when subjected to compressive loads.
Consists of a frame with a bottom ring and a top ring with tightening screws to firmly clamp the compressometer over the cylinder. A dial gauge .002mm x 5mm is mounted on the upper ring and the tie of the dial gauge rests on an anvil. The zero on the dial gauge can be set by adjusting the anvil screw.
Lateral Extensometer For Testing Lab For Concrete Testing Lab
Lateral Extensometer for Concrete Testing - This is for determining the lateral extension of 15cm dia x 30 cm high cement concrete cylinders while testing them under compression. The unit consists of two movable frames pivoted at one end.
The extensometer is fixed to the specimen with the help of tightening screws. The lateral extension is indicated on a dial gauge of 0.002mm x 5mm is mounted on the upper ring and the tip of the dial gauge rests on an anvil.
Demountable Mechanical Strain Gauge For Testing Lab For Concrete Testing Lab
Demountable Mechanical Strain Gauge for Concrete Testing - It is used for finding out the linear deformation caused on two reference points fixed on a loading member. This portable gauge is designed for a gauge length of 20 cm. of the reference pins. The deformation is indicated by a 0.002 x 5mm dial gauge attached to the instrument.
Vibrating Table For Testing Lab For Concrete Testing Lab
Vibrating Table for Concrete Testing - Designed to carry a load of 140 kg . The apparatus consists of a motor fitted with a variable pitch pulley housed in a cabinet. The vibrations are imparted by means off-balance masses rotating on a shaft of a vibrator clamped to the underside of the table top.
The table top is 50cm x 50cm and has stops along its edges to prevent moulds from walking off the table during vibration . A crass arm adjustable on a vertical rod at the centre of the table is provided to hold the moulds while operating the between a maximum of 3600 vibrations down to 2600 vibration per minute.
Plastic Curing Tank For Testing Lab For Concrete Testing Lab
Plastic Curing Tank for Concrete Testing - Heavy plastic curing tank 650 liters capacity. Extremely robust and stable polyethylene construction, supplied complete with base rack.
Curing Tank For Testing Lab For Concrete Testing Lab
Curing Tank - 24 Hour cycle from time of mixing for Concrete Testing - Controlled 35oC or 100oC ±2oC Curing Temperature for concrete. Controlled 27oC ± 2oC Curing Temperature for grey cement. The tank has been designed to accommodate 150mm/70.6mm cube moulds upto 36/72 cube mould and fully insulated, complete with a hinged lid, heater, thermostat and re-circulated pump. Provision of two removable racks allowing free circulation of water around each mould. The pump, drain valves and electrical equipment are housed in a compartment located at one end of the tank.
Melting Pot For Testing Lab For Concrete Testing Lab
Melting Pot for Concrete Testing - Used to melt Capping compound this pot comprises a metal container in a well lagged steel jacket. A thermostatic control and stand by heat switch are fitted. Supplied complete with lift off cover. Warmer : An electrically heated and thermostatically controlled bath for melting the capping compound.
Supplied with cover and handle. Suitable for operation on 230 Volts A.C. Single Phase. Capping Compound : Used for capping the ends of concrete cylinders to be tested. Available in packs of 5 kg. Bowl & Ladle : Metallic bowl is used to carry the capping compound and ladle is used to pout molten capping compound in to the groves between specimen and capping plate.
Capping Set (Vertical) For Testing Lab For Concrete Testing Lab
Capping Set (Vertical) for Concrete Testing - For capping compression cylinder specimens. This apparatus can be used both in the laboratory and in the field. The specimens capped in this apparatus have plane parallel faces. For cylinders 150mm dia x 300mm long. Consists of a base with an upright.
The upright serves as a guide for positioning the capping plate and cylinder. The 19mm thick capping plate is machined accurately. There is a recess in the plate for keeping the molten capping compound and to position cylinder. Complete with cylinder carrier and ladle.
Capping Set (Horizontal) For Testing Lab For Concrete Testing Lab
Capping Set (Horizontal) For 15cm dia x 30cm length cylinders for Concrete Testing - The set comprises of a cylinder capper, a cylinder carrier and a ladle. The cylinder capper consists of a base on which two accurately machined plates are mounted vertically. One plate is firmly fixed and the other one is adjustable horizontally.
Two plates are provided with holders for holding the cylinder in position. The holder are split and the bottom half of each holder is fixed firmly and the top half of each is removable and bolted down to the lower half. On the upper parts of the vertical plates 'V' s are provided for pouring the capping compound. Two spacers are also provided.
Gang Mould (Three Gang) For Testing Lab For Concrete Testing Lab
Gang Mould (Three Gang) for Concrete Testing - Moulding of 40mm, 50mm, 100mm specimens. Manufactured from Mild Steel / Cast Iron / Bronze and supplied complete with base plate.
Beam Mould For Casting For Testing Lab For Concrete Testing Lab
Beam Mould For casting, concrete specimen for flexure tests for Concrete Testing - Made of Cast Iron / Mild Steel. The mould are made of 4 plates assembled together. Each mould is supplied complete with base plate. Faces are machined flat to ± 0.2mm.
Cylindrical Mould For Testing Lab For Concrete Testing Lab
Cylindrical Mould for Concrete Testing - For testing concrete cylinders for compressive strength tests. The moulds is split vertically into two parts. The mean internal diameter in within +/-0.2mm and height is within +/-1mm. The ends are machined to +/-0.05.
Cube Mould For Testing Lab For Concrete Testing Lab
Cube Mould for Concrete Testing - These are available in different sizes and are made according to Indian and British standards . For the metric size cube mould, the faces aremachined flat to +/-0.2mm accuracy and finished to within 0.2mm.
Straight Edge For Testing Lab For Concrete Testing Lab
Straight Edge for Concrete Testing - Used to remove excess material when molding cube and cylinder speciments. Conduction slump cone and air meter tests. Flat bar made from steel. Size: 2” X 18” (5.1 X 45.7CM) 1” X 12\" (2.5 X 30.4CM)
Tamping Bar For Testing Lab For Concrete Testing Lab
Tamping Bar for Concrete Testing - This is used for compacting concrete into cube moulds. This rod is made of steel it is 16mm dia., 600mm in length and rounded at both ends.
Tamping Rod For Testing Lab For Concrete Testing Lab
Tamping Rod for Concrete Testing - This is used for compacting concrete into cube moulds. This rod is made of steel it is 16mm dia., 600mm in length and rounded at both ends.
Laboratory Pan Mixer 56 LTS (Motorised) For Testing Lab For Concrete Testing Lab
Laboratory Pan Mixer 56 LTS (Motorised) for Concrete Testing - This muliflow mixer absorbs fewer air during mixing, requires shorter mixing time and grants a perfect homogeneity in mixtures having a low water and cement ratio. The pan is easily removable by means of a trolley.
Laboratory Concrete Mixer (Motorised) For Testing Lab For Concrete Testing Lab
Laboratory Concrete Mixer (Motorised) for Concrete Testing - A Concrete and mortar mixer for light professional and DIY use. Designed to give reliable service with low maintenance requirements. The compact storage size makes the Mixer a convenient product for DIY users.
Gauging Trowel For Testing Lab For Concrete Testing Lab
Gauging Trowel for Concrete Testing - Weight approximately 210 gms. Best quality with hard wood handle blade length 200mm.
Cone Penetrometer For Mortar For Testing Lab For Concrete Testing Lab
Cone Penetrometer for Mortar for Concrete Testing - For determining the consistency of masonry mortar Consists of a movable bearing rod to which a cone 145mm. Long and 75mm dia at a base is fixed. The bearing rod passes freely through a bracket which is provided with release mechanism. A dial graduated in mm with rack and pinion is provided for measuring the penetration.
Mortar Penetrometer For Testing Lab For Concrete Testing Lab
Mortar Penetrometer for Concrete Testing - It is used for finding out the rate of hardening of mortar sieved from concrete spring and a stem graduated from 0-70 kg x 1 kg. Six interchangeable penetration needles of areas 645, 323, 65 32 and 16mm sq. Is provided .
Pocket Concrete Penetrometer For Testing Lab For Concrete Testing Lab
Pocket Concrete Penetrometer for Concrete Testing - For fast evaluation of the initial setting of concrete. It can be used on light weight concrete, special roof deck mixes and concrete additives.
Specification
Consists of a needle having face area 3/10 sq. cm. and graduated at a distance of 25cm.
KELLEY Ball Penetration Apparatus For Testing Lab For Concrete Testing Lab
KELLEY Ball Penetration Apparatus for Concrete Testing - The apparatus is used to determine the workability of Portland cement & concrete. The Kelly ball test is considered to be simple and much faster than the slump test. Twice the Kelly ball reading approximately equals the slump.
Compaction Factor Apparatus For Testing Lab For Concrete Testing Lab
Compaction Factor Apparatus for Concrete Testing - The apparatus is used for determining the workability of fresh concrete, provided the maximum size of the aggregate does not exceed 38mm. The test is particularly useful for concrete mixes of very low workability where true slump values are not reliable.
Southard Viscometer For Testing Lab For Concrete Testing Lab
Southard Viscometer for Concrete Testing - Putty consistency can be adjusted using this instrument. A 50mm I.D. metal cylinder is mounted on a wooden platform. A close fitting piston moves up to down without turning in this cylinder. Working stroke is 65mm.
Slump Test Apparatus For Testing Lab For Concrete Testing Lab
Slump Test Apparatus for Concrete Testing - It is used for the determination of the consistency of freshly mixed concrete, where the maximum size of the aggregate does not exceed 38mm. Specification : The apparatus consists of one slump cone with handles and foot pieces.
VEE BEE Consistometer For Testing Lab For Concrete Testing Lab
VEE BEE Consistometer for Concrete Testing - The instrument is used for workability as well as consistency of fresh concrete. A slump Cone and a graduated rod supplied with the instrument helps the operator to find out slump values and vibration table with container and acrylic disc is used to find out workability of concrete expressed in Vee Bee degrees,
Item has been added to cart. Subtotal $200.